Description
The composition of the air source processor includes an air filter, a pressure reducing valve, and an oil mister. Some brands of solenoid valves and cylinders can realize oil-free lubrication (lubrication function by grease), and no need to use an oil mister! The filtration degree is generally 50-75μm, and the pressure regulation range is 0.5-10Mpa. If the filtration accuracy is 5-10μm, 10-20μm, 25-40μm, and the pressure regulation is 0.05-0.3Mpa, 0.05-1Mpa, the three major parts are free from tube The connected components are called triple pieces. The three major parts are indispensable air supply devices in most pneumatic systems. Installation in the vicinity of gas equipment is the final guarantee of compressed air quality. The installation sequence of the three large parts is air filter, pressure reducing valve and oil mister respectively according to the direction of intake air. The combination of the air filter and the pressure relief valve can be referred to as a pneumatic two-piece. It is also possible to combine the air filter and the pressure reducing valve together to become a filter pressure reducing valve (the function is the same as the air filter and the pressure reducing valve). In some cases where the presence of oil mist in the compressed air cannot be allowed, an oil mist separator is required to filter out the oil mist in the compressed air. In short, these components can be selected as needed, and they can be combined and used. The air filter is used to clean the air source, and can filter the moisture in the compressed air to prevent the moisture from entering the device with the gas. The pressure reducing valve can regulate the air source to make the air source in a constant state, which can reduce the damage to the hardware of the valve or the actuator when the air source pressure suddenly changes. The filter is used to clean the air source and filter the moisture in the compressed air to prevent moisture from entering the device with the gas. The lubricator can lubricate the moving parts of the body, can lubricate the parts that are inconvenient to lubricate, and greatly prolong the service life of the body.
1. The filter drainage has two methods, pressure differential drainage and manual drainage. When draining manually, it must be drained before the water level reaches the level below the filter element.
2. When adjusting the pressure, please pull up and rotate before turning the knob. Press the rotary knob to position. Turn the knob to the right to increase the outlet pressure, and to the left to decrease the outlet pressure. When adjusting the pressure, it should be gradually and evenly adjusted to the required pressure, and it should not be adjusted in one step.
3. How to use the oil feeder: Use JIS K2213 oil (ISO Vg32 or equivalent oil) for the oil feeder. Please do not add more than eight full cups. The number 0 is the minimum amount of oil and 9 is the maximum amount of oil. Since the 9-0 position cannot rotate, it must rotate clockwise.
1. The air source processor has a simple structure, light weight, and simple installation and maintenance. The medium is air, which is less flammable than the hydraulic medium. Therefore, it is safe to use.
2, the working medium is inexhaustible air, the air itself does not spend money. The exhaust gas treatment is simple, does not pollute the environment, and has low cost.
3, the output power and working speed adjustment is very easy. The operating speed of the cylinder is generally less than 1M/S, which is faster than the hydraulic and electrical modes.
4, high reliability and long service life. The number of effective operation of electrical components is about one million times, while the lifetime of general electromagnetic valves is more than 30 million times, and some good quality valves exceed 200 million times.
5. Using the compressibility of air, it can store energy and realize centralized gas supply. Energy can be released for a short period of time to achieve high-speed response during intermittent exercise. Buffering can be achieved. It has strong adaptability to impact load and overload. Under certain conditions, the pneumatic device can be self-retaining.
6, full pneumatic control with fire, explosion-proof, moisture-proof ability. Compared with the hydraulic method, pneumatic can be used in high temperature applications.
7, due to the small air flow loss, compressed air can be concentrated supply, long-distance transmission.
Reviews
There are no reviews yet.